Instructions how to
install industrial dishwashers from Korea
Instructions how to install
industrial dishwashers from Korea- INKO.VN give you instructions on
how to install industrial dishwashers from Korea effectively, in order to help
you when used, not afraid of leakage of water supply lines or damaged
electrical lines.
1. Preparation before installation
- Disconnect the device from the packing and check for
damage during shipping. If damaged, you must contact the retailer and do not
install device
- Check the device by placing it to the other side or the
back exposed to cupboard or wall
- Place the machine on the flat and solid concrete floor.
If the floor is not flat, then adjust the device until it reaches the vertical
position. If the device is set at a reasonable height,it will be more balanced,
less vibration and less noise during operation.
2.Installation
Attention:
- Connection of water
supply and power supply should be done
by skilled technical staff
- Industrial dishwasher from Korea should not be placed on soft line water
supply or electrical cable supply
- Equipment should use the new pipeline connected to the
water network. Do not use old pipes.
electrical connection
- For personal safety, never use long wire or plugs for
industrial dishwashers from Korea.
- Under any circumstances, never cut or remove third tube
from power.
- Make sure that you have proper wire connect to ground before using the machine
After ensuring voltage and frequency of the current electric
corresponds with the table norms and power system are sized for the maximum
voltage level, set the plug to the power outlet which is connect to the ground .
If the power outlet is incompatible with
the plug, it is better to replace the outlet than using an adapter
which may cause overheating or fire.
Electrical requirements:
See label norms to know about the rated voltage and connect
suitable power for industrial dishwashers from Korea. Use
breaker or fuse to delay time and provide separate circuit for the machine.
Attention:
Install device of cable power supply and socket is kind of
easy to use
Cable is not bent or compressed
If the cable is damaged, it must be replaced by
manufacturers or service technical support to ensure that does not cause
dangerous .
The company is not responsible for any accidents that occur
if these regulations can not be achieved.
Intruction of connection to the ground floor
Dishwasher must be connected to the ground floor.In case of malfunction or
damage,connection to the ground will
reduce the risk of electrical short by
providing one resistance of minimum power circuit .The machine is equipped with
conductor wires and plug connected to
the ground. Plugs should be plugged into the appropriate power outlet which is
installed grounded with local rules and regulations.
Attention:
Error due to unsuitable connection to the ground can lead to
risk of short circuit. Contact the service center if there is suspicion of unsuitable connection .
Do not change the plug which is supplied with the machine. If the plug does not
fit the socket, require a technical staff to buy a suitable outlet in order to
install. To avoid remaining water in
pipeline, lock the shower when using.
Connect to the pipe water supply
Instructions of connecting pipe water for industrial
dishwashers from Korea
+ Connect the cold water source
Connect the water pipe supply to junction with diameter 3/4 inch ,
ensure tight junction and no water leakage.If water supply lines is new and not
used in one period of time, let the water run for a time to ensure clean water
and no impurities. If if this test step is not done, it can lead to jammed
water supply lines and damage the machine
+ Connect the hot water source
Water supply pipes may be connected to the hot water system
in the house,as long as it does not exceed 60 degrees. In this case, the
duration of the wash cycle will be shortened about 15 minutes and productivity
wash will be reduced
Connect the hot water line as cold water line
Device installation
Place the machine into the desired position. The back of
machine against the wall behind the machine and the edges of machine along
cabinets or wall. The machine is equipped with water supply and drain pipes can
be placed in the right or left for more convenient during installation
Connect to water drain
Instruction: connect water drain for industrial dishwashers
from Korea
Install water drain into the exhaust pipe without attached.
If
the length of pipe is not appropriate, it is necessary to apply the necessary
measures to extend, for example use the same material related as original . Remember that the length of
pipe should not exceed 4 meters
including prolonged
>>> Read more
- Industrial Washing Machine
- industrial ovens
- industrial dryer
- Chemical industry
- Electric boiler
If drain water is longer than 4m , dishes will not be
cleaned with discharge line to avoid being left out during washing.
Safety of Water
Source
The system of safety water source is one safe value system
to prevent water leakage.If there is
leakage in the water supply pipe during washing, the safety valve will
interrupt water. Do not soak the water supply or the safety valve in the water
because the power cables of the valve located in the water supply pipe.
If the water supply pipe or safety valve is damaged, remove
the plug from the power outlet immediately. Do not extend or shorten the water
supply because it contains electrical parts.
See more articles about quotation of industrial dishwashers
Conveyor Industrial dishwasher
Models installation
of industrial dishwasher high capacity
Other models of Conveyor Industrial dishwasher